MaxiMite, DuinoMite & CGMMSTICK1 GPIO Tester.

All Dontronics Maximite Computer products are located at: http://www.dontronics-shop.com/the-maximite-computer.html

This product can be found at: http://www.dontronics-shop.com/test-a-mite.html

This device attaches to the 26 pin IDC male header at the rear of your Maximite or DuinoMite. It also has provision for a 30 pin header that is compatible with the CGMMSTICK1 pinout.

Mick Gulovsen designed a tester PCB (called Test-A-Mite) that will put the MaxiMite and DuinoMite through its paces and test the following features are working correctly on our `mites.

Analog Input
Digital Input & Output
Frequency Input
Period Input
Count Input

It also has a few LED Demo routines for Fun and lets face it who doesnt like fun..

Fun LED chases as follows:

Simple LED Chase
LED Bar Graph Display
LED Cross Over
Binary Counting

All information can be found HERE including some short video clips of a DuinoMite-mini connected to the Test-A-Mite doing each of the Fun LED chases

The schematic and part list is all available above so it is not too hard to make your own, or PCBs are available from Dontronics for $5.95AUD, or $7.95AUD including World wide Postage in a LETTER

NOTE ***

This PCB can also be used as a CGMMSTICK1 to 26 pin IDC connector adapter board.

The Test-a-Mite

We can post off the Test-a-Mite bare printed circuit board in a letter, world wide at a very cheap rate. In fact, we will do it for an extra $2. See this Page for details: 
www.dontronics-shop.com/test-a-mite-letter.html

This is an all through hole design, so the user can build it easily themselves. Anyone who has done a little electronics work, should have very little trouble soldering this kit together.

The board measures 81.3mm by 71.1mm (3.2" by 2.8") , 1.6mm thickness.

As many parts may be awkward to chase up, we have given detailed instructions on where they can be obtained in the PDF manual.

The parts we do have readily available are listed in the bundled groups of prices below. This includes a R/A 26 pin IDC female connector, and a R/A 26 pin IDC male connector for the input and output of this board.

You may also like to purchase a 26 pin 10cm IDC Female to Female header cable. This may be handy if your board design doesn't allow the Test-a-Mite to plug straight into the MaxiMite, or DuinoMite board. At times, power cables, USB cables, or other connectors, may be blocking your path. Check this out. You may need a cable.

Prices: We have set up prices starting at $5.95 for a PCB only, to $12.95 for the parts we have available:

Bare Test-a-Mite PCB: $5.95AUD
Bare Test-a-Mite PCB

Bundle A: $9.95AUD
Bare Test-a-Mite Printed Circuit Board, plus a 26 pin 10cm IDC Female to Female header cable.

Bundle B: $8.95AUD
Includes Test-a-Mite PCB
plus a R/A 26 pin IDC female connector, and a R/A 26 pin IDC males connector.

Bundle C: $12.95AUD
IncludesTest-a-Mite
PCB plus a 26 pin 10cm IDC Female to Female header cable, plus a R/A 26 pin IDC female connector, and a R/A 26 pin IDC males connector.

The Bundled kits do not include all parts. Only the items included above.

 


Software Download:

All software can be downloaded from: HERE

Schematics and all other relevant files are available from: HERE
 


Support:

If you need additional support on the above product, and you can't find the information you need in the documentation, then please contact support at the address below:


Support Forum:
http://www.kenseglerdesigns.com/cms/forums/index.php
http://www.thebackshed.com/forum/forum_topics.asp?FID=16&PN=1

This product is from: Dontronics

The Maximite Computer Blog
http://www.duinomite.com/

 

This entry was posted in News and tagged , , , , , , . Bookmark the permalink.

Comments are closed.